基于遥感尾气监测的柴油车气态污染物排放因子计算方法研究

采用遥感尾气测试系统实测了柴油车在实际道路工况下的CO、HC和NO排放特征,修正了排放因子的计算方法,并与车载排放测试系统（PEMS）实测结果进行了验证,获得了实测车辆的CO、HC和NO排放因子.测试结果显示,在各种遥感监测的工况下柴油车尾气中均含有较高浓度的氧气,未考虑氧气影响的燃烧方程反演获得的各污染物体积浓度计算值与PEMS实测值的偏差较大,且氧气浓度越大,偏差越大.经过氧气修正的燃烧方程反演计算的尾气浓度与PEMS实测值吻合度大幅提升,适用于实际工况下遥感检测车辆尾气的反演计算.修正算法得到CO、HC和NO的排放因子离散性较小,精确度较高,可以为量化柴油车尾气排放贡献提供科学依据.     

基于稳定氢同位素的太原市大气单环芳烃来源

采集太原市城北和城南区域环境空气和5类污染源挥发性有机物样品,测定样品中典型单环芳烃稳定氢同位素（δD）组成,基于同位素质量平衡原理计算单环芳烃从源到环境空气受体的δD初始混合值,探讨单环芳烃来源.结果表明,柴油挥发源、溶剂挥发源、汽油挥发源（97^#）、汽油挥发源（95^#）、机动车尾气（97^#）、机动车尾气（95^#）和民用燃煤源中单环芳烃δD范围依次为：（-138.7‰~-115.5‰）、（-147.0‰~-121.0‰）、（-150.8‰~-117.6‰）、（-131.8‰~-113.8‰）、（-171.2‰~-120.0‰）、（-138.9‰~-102.7‰）和（-168.3‰~-142.3‰）,民用燃煤源中单环芳烃δD显著贫重氢同位素（D）组成,机动车尾气源与汽油挥发源中苯的δD相比显著贫D,可用于探索污染物转化过程;城北和城南环境空气中δD范围为（-131.7‰~-115.1‰）和（-131.9‰~-74.9‰）,δD初始混合值为-138.4‰和-173.9‰,体现了其来源差异.     

金属表面涂装行业VOCs排放特征及排放系数

对比了浙江省2014和2018年金属表面涂装企业的有机废气排放及治理情况,分析了该行业涂料及稀释剂的使用、主要污染因子,测算了溶剂型、水性涂料的挥发性有机物（VOCs）产生系数和排放系数.结果表明：2018年VOCs治理水平明显高于2014年,水性涂料使用企业比例由18%上升至36%,纯溶剂型企业由82%下降至64%;金属表面涂装行业的主要排放污染物为二甲苯、丁醇、乙酸乙酯、乙酸丁酯、甲苯、丙二醇、乙苯、苯乙烯等8种有机物.溶剂型和水性涂料的VOCs产生系数分别为0.72和0.31kg/kg;溶剂型和水性涂料2014年VOCs排放系数为0.64和0.29kg/kg,2018年为0.48和0.21kg/kg.     

DOC+CDPF对国III重型柴油货车实际道路排放的影响

利用便携式车载排放测试系统（PEMS）对2辆加装氧化催化转化器（DOC）和催化型柴油颗粒捕集器（CDPF）与否的国III重型柴油货车进行实际道路排放测试.结果表明,2辆改造重型柴油车的CO、THC、固态颗粒物粒数（SPN）和黑碳（BC）实际道路排放因子分别为（1.31±0.37）g/（kW×h）、（0.20±0.03） g/（kW×h）、（7.13×10¹⁰±5.27×10¹⁰）个/（kW×h）和（0.69±0.06）mg/（kW×h）,相对于原始排放（拆除DOC+CDPF）分别降低52.48%、55.69%、99.91%和99.22%.从低速、中速到高速,CO和THC减排比例呈现上升趋势,然而运行工况对SPN和BC减排比例则无显著影响.加装DOC+CDPF会导致NO₂在NO_x中的占比升高,且从低速、中速到高速涨幅依次增大,但对NO_x无明显减排效益,其排放因子为9.53~9.83g/（kW×h）,远高于实验室排放限值.     

Regulated emission characteristics of in-use LNG and diesel semi-trailer towing vehicles under real driving conditions using PEMS

On-road driving emissions of six liquefied natural gas(LNG) and diesel semi-trailer towing vehicles(STTVs) which met China Emission Standard IV and V were tested using Portable Emission Measurement System(PEMS) in northern China.Emission characteristics of these vehicles under real driving conditions were analyzed and proved that on-road emissions of heavy-duty vehicles(HDVs) were underestimated in the past.There were large differences among LNG and diesel vehicles, which also existed between China V vehicles and China IV vehicles.Emission factors showed the highest level under real driving conditions, which probably be caused by frequent acceleration, deceleration, and start-stop.NOx emission factors ranged from 2.855 to 20.939 g/km based on distance-traveled and 6.719–90.557 g/kg based on fuel consumption during whole tests, which were much higher than previous researches on chassis dynamometer.It was inferred from tests that the fuel consumption rate of the test vehicles had a strong correlation with NOx emission, and the exhaust temperature also affected the efficiency of Selected Catalytic Reduction(SCR) aftertreatment system, thus changing the NOx emission greatly.THC emission factors of LNG vehicles were 2.012–10.636 g/km, which were much higher than that of diesel vehicles(0.029–0.185 g/km).Unburned CH_4 may be an important reason for this phenomenon.Further on-road emission tests, especially CH_4 emission test should be carried out in subsequent research.In addition, the Particulate Number(PN) emission factors of diesel vehicles were at a very high level during whole tests, and Diesel Particulate Filter(DPF)should be installed to reduce PN emission.     

Reactive uptake of NO2 on volcanic particles: A possible source of HONO in the atmosphere

The heterogeneous degradation of nitrogen dioxide (NO₂) on five samples of natural Icelandic volcanic particles has been investigated. Laboratory experiments were carried out under simulated atmospheric conditions using a coated wall flow tube (CWFT). The CWFT reactor was coupled to a blue light nitrogen oxides analyzer (NO_x analyzer), and a long path absorption photometer (LOPAP) to monitor in real time the concentrations of NO₂, NO and HONO, respectively. Under dark and ambient relative humidity conditions, the steady state uptake coefficients of NO₂ varied significantly between the volcanic samples probably due to differences in magma composition and morphological variation related with the density of surface OH groups. The irradiation of the surface with simulated sunlight enhanced the uptake coefficients by a factor of three indicating that photo-induced processes on the surface of the dust occur. Furthermore, the product yields of NO and HONO were determined under both dark and simulated sunlight conditions. The relative humidity was found to influence the distribution of gaseous products, promoting the formation of gaseous HONO. A detailed reaction mechanism is proposed that supports our experimental observations. Regarding the atmospheric implications, our results suggest that the NO₂ degradation on volcanic particles and the corresponding formation of HONO is expected to be significant during volcanic dust storms or after a volcanic eruption.     

Coupling mechanism of activated carbon mixed with dust for flue gas desulfurization and denitrification

To clarify the effect of coking dust, sintering dust and fly ash on the activity of activated carbon for various industrial flue gas desulfurization and denitrification, the coupling mechanism of the mixed activated carbon and dust was investigated to provide theoretical reference for the stable operation. The results show that coking dust had 34% desulfurization efficiency and 10% denitrification efficiency; correspondingly, sintering dust and fly ash had no obvious desulfurization and denitrification activities. For the mixture of activated carbon and dust, the coking dust reduced the desulfurization and denitrification efficiencies by blocking the pores of activated carbon, and its inhibiting effect on activated carbon was larger than its own desulfurization and denitrification activity. The sintering dust also reduced the desulfurization efficiency on the activated carbon while enhancing the denitrification efficiency. Fly ash blocked the pores of activated carbon and reduced its reaction activity. The reaction activity of coking dust mainly came from the surface functional groups, similar to that of activated carbon. The reaction activity of sintering dust mainly came from the oxidative property of Fe₂O₃, which oxidized NO to NO₂ and promoted the fast selectively catalytic reduction (SCR) of NO to form N₂. Sintering dust was activated by the joint action of activated carbon, and both had a coupling function. Sintering dust enhanced the adsorption and oxidation of NO, and activated carbon further promoted the reduction of NO_x by NH₃; thus, the denitrification efficiency increased by 5%-7% on the activated carbon.     

郑州市VOCs组分排放清单及其臭氧生成潜势

基于人为源挥发性有机物（VOCs）活动水平统计和源成分谱梳理,采用排放因子法,建立了郑州市2016年VOCs组分排放清单,评估了各类源臭氧生成潜势（OFP）.结果表明,2016年郑州市人为源VOCs排放总量为96215.3 t,排放量最高的是道路移动源（29.7%）,其次是有机溶剂使用源（28.1%）;排放量最高的组分是烷烃（29.8%）,其次是芳香烃（29.0%）.郑州市人为源VOCs的OFP为341291.0 t,贡献最高的排放源是道路移动源（30.5%）,其次是溶剂使用源（28.8%）,其中轻型汽油车、内墙涂料使用、机动车表面涂层、加油站装卸油和非金属矿物制造是OFP的主要次级排放源,也是郑州市降低臭氧污染时需重点管控的VOCs排放源.对于VOCs种类而言,贡献较高的是芳香烃（42.8%）,其次是烯烃（38.9%）,未来应加强对间/对-二甲苯、丙烯和乙烯等物种排放来源的控制.     

不同居民燃煤炉具大气污染物排放差异性及减排分析

为探究不同类型炉具的大气污染物排放差异,本研究选择5种常见的新式居民燃煤炉具（方型煤炉具、折流换热炉具、炕暖炊一体化炉具、气化正烧及气化反烧炉具）在实验室内进行模拟燃烧和大气污染物排放水平监测,定量评估不同炉具的环境效果,识别污染排放水平差异的影响因素及原因,从而提出炉具研发设计等污染减排的改进建议.结果表明：①不同炉具大气污染物排放差异较大,炕暖炊一体的炉具污染排放强度最大,3种大气污染物（SO₂、NO_x和颗粒物）的排放强度为2.9 kg ·t^-1,是平均值的1.6倍;应用方型煤技术的炉具大气污染物排放强度最低,是平均值的65%.②不同炉具在不同燃烧阶段其气态污染物排放也呈现出明显的差异和特征.旺火阶段方型煤炉具NO_x排放浓度为0.49mg ·m^-3,相较于其他类型炉具降低了45%~72%;气化反烧炉具的SO₂排放浓度为1.38mg ·m^-3,相较于其他类型炉具最高降低了28%.③影响炉具大气污染物排放因素包括应用技术及燃烧类型,采用方型煤及气化反烧技术的炉具环境效益较好,但两类炉具的经济成本分别达到2.0万元和1.8万元,明显高于其他类型炉具.④考虑不同炉具污染排放差异,建议采取差异化的经济政策和严格的排放和产品标准,推广使用节能环保型炉具,降低燃煤炉具大气污染物排放.     

海绵城市地块汇水区颗粒污染物的传输

目前我国海绵工程建设多集中在地块汇水区单元内开展,通过多个低影响开发(LID)设施协同完成地表径流水质水量的调控,但基于地块汇水区尺度下城市面源污染的产生和控制效果鲜有报道.本研究比较分析了不同硬化率地块汇水单元内的面源颗粒污染物晴天累积、降雨冲刷、地表径流及径流输出负荷状况.结果表明,地块汇水单元内硬质路面是面源颗粒污染物贡献的最主要的下垫面类型,中硬化率(61.1%)地块和高硬化率(73.6%)地块路面街尘累积量分别约占汇水区单元的88.4%(2.22～12.51 g·m~(-2))和90.1%(4.99～33.43 g·m~(-2)),对径流SS的输出贡献比率分别约为91.7%(0.97～7.34 g·m~(-2))和90.5%(0.92～18.77 g·m~(-2)),降雨径流SS污染负荷占比分别约为95.2%和83.1%,经LID设施处理后输出径流污染负荷约为地表径流的24.0%和40.2%.硬质路面的街尘晴天累积及降雨冲刷以150μm为主,地表径流及输出径流则以50μm粒径段为主,同时地块不透水比例的增加,细粒径(105μm)颗粒物的累积及冲刷分布增大(24.4%和106.4%),而粒径50μm的颗粒物在路面径流中的分布减小(12.4%).屋面的街尘累积、冲刷及降雨径流的粒径分布状况与硬质路面大致相似,但中硬化率地块(1 000μm)和高硬化率地块(250～450μm、45μm)在3个粒径段范围的颗粒物累积和冲刷相较于路面街尘粒径分布明显增加(1 000μm:58.1%和108.5%; 250～450μm:72.9%和41.8%;45μm:59.2%和64.8%).以上结果揭示了颗粒污染物在地块汇水区尺度下的污染全过程(累积-冲刷-输出)分布及LID设施对地块整体SS污染负荷的控制效果,可为地块汇水单元内LID设施工程绩效的科学评估提供重要参考.